4 Channel Starter Kit: Key Fob - 4 Channel Controller
Product No: LS3KIT4KF
3 in stock
The Light Symphony 4 channel Keyfob Starter Kit comprises one 4 Channel Lighting Control Unit and one 4 channel keyfob control
£382.80
- Product Overview
- More Information
- Downloads
- Reviews
The Light Symphony 4 channel Keyfob Starter Kit comprises one 4 Channel Lighting Control Unit and one 4 channel keyfob control. Each channel is fully rated for an inductive load for remote control of fluorescent outdoor lighting, low voltage garden lighting or metal halide exterior lighting without de-rating. The 4 Zone Key Fob has a hard wearing stainless steel facia, sliding key cover and 350m range for use with LIGHT SYMPHONY 1, 2 and 4 zone remote control units
This Lighting Control Module (LCM) provides 4 wirelessly controllable outputs each rated at up to 1000W and suitable for all load types. It provides flexible control for any lighting circuit or pump and is quickly configurable as a simple switch, group (zone) or scene controller, with 29 zone memories for individual circuits or zones and a master on/off.Outputs 1 and 2 can be programmed as a switched or dimmable output. Outputs 3 and 4 are not dimmable by default: user dimming can be enabled if the total load is under 500w per channel (2kw) total. The dimming mode provides a soft-on, soft-off feature with filament pre-heating, which can greatly increases lamp life.The separately fused outputs are fully protected against over current and over temperature. Large 10mm? cable terminations, standard (20mm) gland cut-outs and an earth bonded gland-chassis simplify installation.The built-in signal-strength indicator, zero-volt mains switching and power-on surge protection all enhance reliability. Lid-on programming speeds commissioning and reduces the risk of water ingress during installation.
This Lighting Control Module (LCM) provides 4 wirelessly controllable outputs each rated at up to 1000W and suitable for all load types. It provides flexible control for any lighting circuit or pump and is quickly configurable as a simple switch, group (zone) or scene controller, with 29 zone memories for individual circuits or zones and a master on/off.Outputs 1 and 2 can be programmed as a switched or dimmable output. Outputs 3 and 4 are not dimmable by default: user dimming can be enabled if the total load is under 500w per channel (2kw) total. The dimming mode provides a soft-on, soft-off feature with filament pre-heating, which can greatly increases lamp life.The separately fused outputs are fully protected against over current and over temperature. Large 10mm? cable terminations, standard (20mm) gland cut-outs and an earth bonded gland-chassis simplify installation.The built-in signal-strength indicator, zero-volt mains switching and power-on surge protection all enhance reliability. Lid-on programming speeds commissioning and reduces the risk of water ingress during installation.
| How to use it | The Lighting Control Module (LCM) ''hears'' the wireless commands from any of Light Symphony''s controllers, such as the keyfob remote control. If a base-station is installed, it will also hear commands from the remote control and echo them. The Lighting Control Modules will ''hear'' both signals, significantly increasing the range and reliability. |
|---|---|
| Range: | 350 metre wireless range line-of-site |
| Enclosure: | IP66, UV stable, ABS plastic with non-penetrating wall-mounts translucent lid & neoprene o-ring. Colour RAL7011 |
| Size: | 225 x 185 x 85mm |
| RF: | 434.075MHz Narrow Band FM. |
| Coding: | Security channels 1-16. |
| Power: | Supply: 230VAC +/-10% 50Hz Standby <1W |
| CE Compliance: | EN220300, EN500811 To EN500821 |
| Channels | 4 Channel lighting controller |
|---|---|
| Type | Lighting Controllers |